Products
High-Temperature Heating-Tube Type Lead-Free Solder Pot
- Product details
-
STANDARD SERIES · HIGH-TEMPERATURE HEATING-TUBE TYPE LEAD-FREE SOLDER POT (800 °C HEATING TUBE)
The high-temperature heating-tube type Lead-Free Solder Pot is the workhorse bench pot of the range: a titanium alloy pot with an 800 °C heating tube and stepless inverter temperature control, for hand dipping and tinning of wire ends, transformer and inductor pins, terminals and lugs. Because the heater runs hot and the pot is built from titanium alloy, it holds up on lead-free (SAC) solder as well as on thick wire and heavy terminal work that a small pot cannot heat fast enough. Power is 500 - 2000 W on 110 - 220 V / 50 Hz and the housing is 201 stainless steel. This is the widest range in the series — 70 inner sizes from 50 × 50 × 50 mm up to 460 × 170 × 50 mm, plus special shapes such as the double dross box and the side-outlet wiring versions, with 40 × 40 mm dross box and 90 × 60 × 50 mm wiring box as standard. Built by FD in Dongguan, Guangdong, China. In the trade the same pot is also called a lead-free soldering pot, a lead-free solder bath or a lead-free tin pot — all these names refer to the same pot.
Product ParametersModel High-temperature heating-tube type — 70 inner sizes, further sizes built to order Also Known As Lead-Free Solder Pot · Lead-Free Soldering Pot · Lead-Free Solder Bath · Lead-Free Tin Pot Heater 800 °C high-temperature heating tube Pot Material (inner) Titanium alloy Housing (outer) 201 stainless steel Power 500 - 2000 W (according to pot size) Voltage 110 - 220 V / 50 Hz Temperature Control Inverter (stepless) temperature control Pot Core Treatment 800 °C high-temperature treatment Dross Box 40 × 40 mm, same width as the pot (double dross box versions available) Wiring Box 90 × 60 × 50 mm Outer Dimensions Inner size + 130 mm length, + 40 mm width, + 50 mm height Pot Core Allowance + 24 mm × 2 on the long sides, + 18 mm × 2 on the short sides Warranty Heating element 3 months, other parts 1 year Specifications are as listed in our catalogue. 70 inner sizes are held from 50 × 50 × 50 mm to 460 × 170 × 50 mm, and any other size is built to order.
Representative SizesInner Size (L × W × D mm) Inner Size (L × W × D mm) Inner Size (L × W × D mm) 50 × 50 × 50 80 × 80 × 50 200 × 80 × 50 60 × 60 × 50 100 × 100 × 50 240 × 80 × 50 70 × 70 × 50 120 × 80 × 50 280 × 80 × 50 150 × 60 × 50 200 × 100 × 50 300 × 100 × 50 160 × 110 × 50 250 × 100 × 50 320 × 120 × 60 350 × 100 × 50 400 × 110 × 50 460 × 170 × 50 A selection from the 70 sizes held. Special versions include double dross box, side-outlet wiring box, extra-deep pots and pots with a J-pattern outlet. Send us the inner length, width and depth you need for a quotation.
Feature Set800 °C high-temperature heating tube — the heater runs hot enough to reflow lead-free solder quickly, so heavy wire, thick terminals and large parts do not stall the bench
Titanium alloy pot — resists the corrosion that lead-free (SAC) solder causes in cast iron and plain stainless steel pots, so the pot lasts far longer
Stepless inverter control — set the running temperature on the dial and the controller holds it; no fixed steps between low and high
70 inner sizes — from 50 × 50 × 50 mm up to 460 × 170 × 50 mm, the widest range in the series
Dross box 40 × 40 mm — a separate pocket, the same width as the pot, so the oxide skin does not sit on the working surface; double dross box versions available for busy benches
Wiring box 90 × 60 × 50 mm — keeps the power lead and the thermocouple clear of the solder area
201 stainless steel housing — protects the heater and the insulation and keeps the outer shell cool enough to handle
Special shapes to order — side-outlet wiring, J-pattern outlets, extra depth and custom footprints
Warranty — heating element 3 months, other parts 1 year
Tell us the largest part you dip and how many pots are on the bench, and we will pick the size and the power rating.
Product OverviewApplication FieldsHeavy Wire & Cable Tinning
Transformer & Inductor Pins
Terminals, Lugs & Busbars
Production Benches
Features800 °C Heating Tube
Titanium Alloy Pot
500 - 2000 W · 110 - 220 V
70 Sizes, 50 × 50 to 460 × 170 mm
AdvantagesHot Enough for Heavy Work
Widest Size Choice in the Range
Long Pot Life on Lead-Free Solder
Factory Direct from Dongguan, China
Lead-Free Solder Pot RangeThe Lead-Free Solder Pot range covers the high-temperature heating-tube type, the ceramic heater type, the oil-resistant ceramic type, the flat-plate type and replacement titanium pot cores. Every pot is built in Dongguan, Guangdong, China — send us your part and pot dimensions for a quotation.
Product Details
Temperature Controller

Solder Pot

Heating Element
Photographs are of the standard model. The pot size and the voltage are set to your order.
Product Demo Video
▶ Click the cover to play the demo video. Contact us for a live working video of this pot on your wire or terminal.
Application ScenariosHeavy Wire & Lugs Thick stranded cable, battery lugs and busbars pull a lot of heat out of a bath; the 800 °C element and the larger pot sizes keep the solder molten through the job. Transformer & Inductor Pins Pin rows are dipped by hand for repair lots and small batches, or where the part cannot be held in a machine fixture. Production Benches Several sizes of part run across one bench; a pot with a large working area and a double dross box keeps the operator dipping instead of skimming. Long or Awkward Parts The 460 × 170 mm and 300 × 200 mm sizes take long parts and wide pin rows that a small bench pot cannot cover in one dip. How To UsePlace the pot on a level, heat-resistant bench and keep the working area dry.
Set the temperature on the inverter controller and let the pot reach it before adding solder.
Add lead-free solder bar until the bath covers the pot floor at the depth you need; top it up through the shift as the level drops.
Skim the oxide skin into the 40 × 40 mm dross box before the first dip and again whenever it builds up.
Apply flux to the wire end or pin group, then dip it squarely and lift it straight out.
Check the tinned length against the drawing and adjust the temperature or dipping time.
Switch off and let it cool before emptying or cleaning the pot.
⚠ Safety notice: molten solder is hot enough to cause severe burns — never reach over the pot, keep the bench dry (molten solder and water contact can cause splatter), wear heat-resistant gloves and eye protection, work in a ventilated area, and isolate the power supply before any service.Frequently Asked QuestionsQ1: What is a Lead-Free Solder Pot?
It is a bench-top heated pot holding a bath of molten lead-free solder, into which wire ends and component pins are dipped by hand. This high-temperature version uses a titanium alloy pot and an 800 °C heating tube. The same pot is also called a lead-free soldering pot, a lead-free solder bath or a lead-free tin pot.
Q2: Why choose the high-temperature type rather than the ceramic type?
The high-temperature heating tube is the one to pick when the parts are heavy: thick cable, large lugs, busbars and wide pin rows pull heat out of the bath and need a heater that recovers quickly. Choose the ceramic type where a more even, gentler heat across the pot floor suits thinner work.
Q3: What sizes are available?
70 inner sizes are held, from 50 × 50 × 50 mm up to 460 × 170 × 50 mm, including 300 × 200 × 65 mm and versions with a double dross box or a side-outlet wiring box. Any other size is built to order.
Q4: What are the power and voltage ratings?
500 - 2000 W depending on pot size, on 110 - 220 V / 50 Hz, with stepless inverter temperature control. Tell us the voltage in your market and we will set the pot accordingly.
Q5: Can I get a pot in a special shape?
Yes. Beside the standard range we build double dross box pots, side-outlet wiring pots, J-pattern outlets, extra-deep pots and custom footprints from your drawing.
Q6: Which industries use a pot like this?
Wire and cable assembly, transformer and inductor making, terminal and lug production, motor and coil winding, and any production bench that dips parts in lead-free solder by hand.
Need a large lead-free solder pot for heavy wire and lugs?Titanium alloy pot · 800 °C heating tube · 500 - 2000 W · 110 - 220 V / 50 Hz · 70 sizes up to 460 × 170 × 50 mm · OEM / ODM available · Factory direct from Dongguan, ChinaGet a Quote
related products
Ultrasonic Solder Pot FD-20014070C | Flux-Free Tinning Machine 200x140 mm Bath
Ultrasonic solder pot FD-20014070C, 200x...
Ultrasonic Solder Pot FD-14014070C | Flux-Free Tinning Machine 140x140 mm Bath
Ultrasonic solder pot FD-14014070C, 140x...
Ultrasonic Solder Pot FD-12012060C | Flux-Free Tinning Machine 120x120 mm Bath
Ultrasonic solder pot FD-12012060C, 120x...
Stainless Steel Explosion-Proof Industrial Oven FD1200800800FBB
Stainless Steel Explosion-Proof Industri...
Product Inquiry
Please leave your message, we will contact you quickly after receiving it, thank you for your support!
common problem
Q
What are the characteristics of cigarette box three-dimensional packaging machine?
A
1. There is no need to adjust the height of the countertops on both sides of the machine when changing the mold, and there is no need to disassemble and assemble the discharge chain or put the hopper, which shortens the four-hour mold replacement time of the traditional machine to only 30 minutes.
2. Adopting a new dual insurance mechanism, the machine does not need to be shut down when it is not running synchronously, nor will it damage other parts.
3. The original one-way hand crank device prevents the machine from shaking in reverse, and the handwheel does not rotate during operation, making the operator safer.
4. The new double rotary film cutting knife can ensure that the machine can be used continuously for many years without a sharpening port, overcoming the defect that the traditional fixed single rotary film cutting blade is easy to wear.
Q
Automatic poker transparent film three-dimensional packaging machine packaging products?
A
Automatic poker transparent film three-dimensional packaging machine is mainly suitable for bulk poker, compressed biscuits, sachima, stickers, sticky notes, wafer biscuits and other bulk or multi-object collection of three-dimensional packaging.
E-mail address:
Hotline:
English
繁体中文
简体中文
Deutsch
Tiếng Việt


